How to Replace Lines in Ryobi String Trimmers

How to Replace Lines in Ryobi String Trimmers

Ryobi gives electric-, gasoline- and battery-powered string trimmers in addition to hybrid fashions that may run on electrical energy when the battery runs out of energy. With such a wide range of trimmer fashions out there, it is smart that Ryobi manufactures a wide range of trimmer heads. The process for restringing a few of these heads, such because the Reel Simple and Professional Reduce II string heads, is the essence of simplicity. In case your trimmer occurs to have the extra standard Common Bump Feed string head, then the restringing process is not rather more tough and takes just some minutes.

Reel Simple String Head

Cease the engine of a Ryobi string trimmer that has a Reel Simple string head. Disable the machine by disconnecting its spark plug wire, unplugging it from {an electrical} outlet or eradicating its battery.

Reduce a 25-foot-long piece of 0.095-inch-diameter monofilament trimmer line from a roll, utilizing a utility knife or scissors for reducing.

Rotate the knob on high of the top till the arrow on the knob strains up with the arrows on the top. Feed one finish of the 25-foot-long trimmer line by way of the opening on the facet of the top, and pull the road by way of from the top’s different facet till you have got two equal lengths of line, or string.

Wind the knob till solely 8 inches of string are left on each side of the top. Wind counterclockwise in case your trimmer has a curved shaft, and wind clockwise if it is a straight-shaft mannequin or a brush cutter.

Professional Reduce II String Head

Flip off the engine of a Ryobi string trimmer that has a Professional Reduce II string head. Disable the trimmer by disconnecting its spark plug wire, unplugging it from {an electrical} outlet or eradicating its battery.

Reduce two 11-inch lengths of trimmer string from a roll. Use both 0.095- or 0.105-inch-diameter monofilament string.

Feed the tip of one of many 11-inch lengths of string into one of many holes on the facet of the trimmer’s head, and push the string by way of till about 1 inch of string protrudes from the highest of the top. Take away all outdated string that comes out of the opening while you feed within the new string.

Set up the opposite 11-inch size of string within the gap on the other facet of the top in the identical approach you put in the primary size of string.

Common Bump Feed String Head

Cease the engine of a Ryobi string trimmer with a Common Bump Feed string head. Disable the trimmer by disconnecting its spark plug wire, unplugging it from {an electrical} outlet or eradicating its battery.

Grasp the string head with one hand, and unscrew the knob on high of it together with your different hand by turning the knob counterclockwise. Take away the knob and trimmer cowl, and raise out the string spool. Pull out all outdated string.

Reduce an 18-foot piece of 0.095-inch-diameter string from a roll, and fold it in half. Hook the middle of the piece of string to the notch within the heart of the spool, and wind each ends of the string across the spool within the path of the arrow printed on the high of the spool. Cease winding when 6 inches are left on every finish of the string.

Return the spool to the top, and slip every finish of the string into one of many slots on the facet of the top. Rotate the spool to align the notches with the slots, and put the duvet again in place.

Screw the knob again into place on high of the string head, turning the knob clockwise to tighten it, and pull the string ends sharply to drag the spool into alignment. Push down on the knob whilst you pull the string ends to make sure the string advances correctly.

Issues You Will Want

Monofilament trimmer line
Tape measure
Utility knife or scissors

Tip

Use solely the string really helpful for the string trimmer’s head. If the string is just too extensive, it will not advance and will overwork the trimmer. If it is too skinny, it will not lower correctly.

Some weedwackers use thicker string than others.
Regardless of the variations among the many many out there fashions of weedwackers — also called string trimmers — all of them have one factor in frequent: they run out of string. Whereas changing the string might be sophisticated on some older fashions, it is normally straightforward to do on up to date ones. Whereas there isn’t any common cap and spool mechanism, the variations aren’t that nice, and if you happen to can restring one weedwacker, you may in all probability restring every other. You may have to seek the advice of the handbook in your mannequin — normally out there on-line — for specific questions.

1
Make sure the weedwacker cannot abruptly come to life whilst you’re engaged on it by pulling off the spark plug wire, unplugging it or eradicating the battery.

2
Flip it over so the string head is going through you and study the string head. If it has a knob, maintain the top with one hand whilst you flip the knob counterclockwise. It will launch the cap from the spool. If the top has two tabs which can be reverse one another, push these in together with your thumb and center digit to launch the cap.

3
Take away the spool from the trimmer shaft and pull out all of the outdated string. Make certain the substitute string is identical diameter. Most trimmers take both 0.080 or 0.065-inch microfilament string. Should you use the flawed string, the trimmer will not work correctly, and you can burn out the motor.

4
Reduce a size of string from a spool with a utility knife. Some fashions take 9 toes of string whereas others can deal with as much as 20, so measure how a lot you want with a tape measure. There isn’t any downside with winding lower than the really helpful most. It simply means you will should restring sooner. Some fashions take two an identical lengths of string.

5
Feed one finish of the string into the opening int he central hub of the spool and wind the string across the hub within the path proven by the arrow marked on the spool. The spool is full when the sting of the wound string is inside 1/4 inch of the outer fringe of the spool. Go away about 6 inches free on the finish and hook the string to one of many notches on the rim of the spool.

6
Wind the second string in the identical path. Hook it to the notch on the other facet of the rim.

7
Put the spool again on the shaft, making certain that the spring is in the identical place it was while you eliminated the spool. Feed the ends of the string by way of the holes within the cap and change the cap. Push on it to have interaction the locking tabs or screw on the knob to carry it.

8
Reconnect the trimmer energy and switch it on for just a few seconds to robotically trim the string to its working size.

Leave a Reply

Your email address will not be published. Required fields are marked *